ATMEGA328P-15AZ【PDF 74/83 页】MCU AVR 32K FLASH 15MHZ 32-TQFP

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录1905

70页 71页 72页 73页 [74页]75页 76页 77页 78页

7810C–AVR–10/12

Atmel ATmega328P [Preliminary]

To avoid unintentional changes of clock frequency, a special write procedure must befollowed to

change the CLKPS bits:

Write the Clock Prescaler Change Enable (CLKPCE) bit to one and all other bitsin

CLKPR to zero.

Within four cycles, write the desired value to CLKPS while writing a zero to CLKPCE.

Interrupts must be disabled when changing prescaler setting to make sure the write procedure is

not interrupted.

8.12

Register Description

8.12.1

OSCCAL – Oscillator Calibration Register

Bits 7..0 – CAL7..0: Oscillator Calibration Value

The Oscillator Calibration Register is used to trim the Calibrated Internal RC Oscillator to

remove process variations from the oscillator frequency. A pre-programmed calibration value is

automatically written to this register during chip reset, giving the Factory calibrated frequency as

specified in Table 28-1 on page 307. The application software can write this register to change

the oscillator frequency. The oscillator can be calibrated to frequencies as specified in Table

28-1 on page 307. Calibration outside that range is not guaranteed.

Note that this oscillator is used to time EEPROM and Flash write accesses, and these write

times will be affected accordingly. If the EEPROM or Flash are written, do not calibrate to more

than 8.8 MHz. Otherwise, the EEPROM or Flash write may fail.

The CAL7 bit determines the range of operation for the oscillator. Setting this bit to 0 gives the

lowest frequency range, setting this bit to 1 gives the highest frequency range. The two fre-

quency ranges are overlapping, in other words a setting of OSCCAL = 0x7F gives a higher

frequency than OSCCAL = 0x80.

The CAL6..0 bits are used to tune the frequency within the selected range. A setting of 0x00

gives the lowest frequency in that range, and a setting of 0x7F gives the highest frequency in the

range.

8.12.2

CLKPR – Clock Prescale Register

Bit 7 – CLKPCE: Clock Prescaler Change Enable

The CLKPCE bit must be written to logic one to enable change of the CLKPS bits. The CLKPCE

bit is only updated when the other bits in CLKPR are simultaneously written to zero. CLKPCE is

cleared by hardware four cycles after it is written or when CLKPS bits are written. Rewriting the

CLKPCE bit within this time-out period does neither extend the time-out period, nor clear the

CLKPCE bit.

Bit

(0x66)

CAL7

CAL6

CAL5

CAL4

CAL3

CAL2

CAL1

CAL0

OSCCAL

Read/Write

R/W

Initial Value

Device Specific Calibration Value

Bit

3210

(0x61)

CLKPCE

–

CLKPS3

CLKPS2

CLKPS1

CLKPS0

CLKPR

Read/Write

R/W

Initial Value

See Bit Description

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式